Page 6 of 7
Re: 1st time on DCG Project
Posted: Mon Apr 02, 2018 1:23 pm
by Zeta
Im using Canon EF-S 18-55mm as a beam expander.
Re: 1st time on DCG Project
Posted: Thu Apr 05, 2018 12:01 pm
by Zeta
Ummm. This is bad.
Is this because too much dichromate?
Or just my bad coating?
- 9A891C56-0DEA-4B40-A4DD-942BF9C97F56.jpeg (1.91 MiB) Viewed 33143 times
Re: 1st time on DCG Project
Posted: Thu Apr 05, 2018 2:22 pm
by Zeta
Model
- 2CEFD044-F231-47AD-845A-37C4A1AA17D8.jpeg (1.63 MiB) Viewed 33139 times
10min exp 50mw green laser
Still no image on it.
- 68C73C78-BBAE-477D-AD76-881E23F1A5E2.jpeg (1.77 MiB) Viewed 33139 times
Re: 1st time on DCG Project
Posted: Thu Apr 05, 2018 6:48 pm
by pluto
Zeta wrote:Ummm. This is bad.
Is this because too much dichromate?
Or just my bad coating?
9A891C56-0DEA-4B40-A4DD-942BF9C97F56.jpeg
Did the plate look like this prior to exposure?
Re: 1st time on DCG Project
Posted: Thu Apr 05, 2018 9:42 pm
by Zeta
Yes
Re: 1st time on DCG Project
Posted: Fri Apr 06, 2018 12:59 pm
by pluto
Zeta wrote:Yes
Yup, seems like you put too much dichromate and it crystallised out.
Re: 1st time on DCG Project
Posted: Sun Apr 08, 2018 2:28 pm
by Zeta
Finally some part of an image appears.
5min exp 50mw 532 30mindark 2min fixer 5min water 2min58% 2min85% 5min99% dry with heat gun
https://youtu.be/rPUqp83xrWM
But only the lower part of the body appears.
- B6AA08E3-5C26-4918-BBF3-159E4E39C94F.jpeg (1.63 MiB) Viewed 33026 times
I have a questions.
After finishing coating the plate and wait for 1hr should I put it in refrigerator(in the box) or just store it in the dark?
My plate looks over or under exposed?
Can dcg be over exposed and what it will look like?
Re: 1st time on DCG Project
Posted: Sun Apr 08, 2018 7:31 pm
by pluto
Zeta wrote:Finally some part of an image appears.
5min exp 50mw 532 30mindark 2min fixer 5min water 2min58% 2min85% 5min99% dry with heat gun
https://youtu.be/rPUqp83xrWM
But only the lower part of the body appears.
B6AA08E3-5C26-4918-BBF3-159E4E39C94F.jpeg
I have a questions.
After finishing coating the plate and wait for 1hr should I put it in refrigerator(in the box) or just store it in the dark?
My plate looks over or under exposed?
Can dcg be over exposed and what it will look like?
After coating you should store the plates in a warm dark place to dry for 4-12 hours. You can store in a refrigerator, but it might cause condensation on the plates. They need to be sealed to prevent this.
Your hologram looks underexposed, overexposure tends to leave a "burned in" effect.
Re: 1st time on DCG Project
Posted: Sun Apr 08, 2018 9:33 pm
by admin_jsfisher
In addition to the under-exposed comments, I think the five minutes in the final alcohol bath seems a bit long. Monitor the final bath under normal lighting. If/when an image appears you are just about done.
Re: 1st time on DCG Project
Posted: Mon Apr 09, 2018 3:25 pm
by Zeta
Came back with nothing.
This is my setup diagram.
- 7301002C-9351-452E-B678-8E596F4E3270.jpeg (348.11 KiB) Viewed 32996 times
Today subjects
- 15AC2D4D-318C-43A9-BBA3-82D1A6B8274A.jpeg (534.86 KiB) Viewed 32999 times
What I got
30mindark 1minfixer 5minwater 1min59% 1min84% 3min99% dry hotgun
- E9F7A673-66AF-451D-AF3F-394B6DD27DE7.jpeg (1.74 MiB) Viewed 32999 times
Is this call burn in effect?
https://youtu.be/kaZUhbqYrts